DIY Cooking Temperature Meter: Difference between revisions
(→ESP32) |
|||
| Line 18: | Line 18: | ||
</gallery> | </gallery> | ||
=== List === | |||
* ESP32: ideaspark® ESP32 Entwicklungsboard 1,14 Zoll 135x240 full color LCD-Display,CH340,WiFi+BL. ST7789 driver, I2C. CH340 | * ESP32: ideaspark® ESP32 Entwicklungsboard 1,14 Zoll 135x240 full color LCD-Display,CH340,WiFi+BL. ST7789 driver, I2C. CH340 | ||
| Line 24: | Line 25: | ||
** Display current 20mA. | ** Display current 20mA. | ||
** Display ports: VCC: VCC, GND: GND, D2(GPIO2): DC, D4: RST, D15: CS, D18: SCLK, D23: MOSI, D32: BLK. | ** Display ports: VCC: VCC, GND: GND, D2(GPIO2): DC, D4: RST, D15: CS, D18: SCLK, D23: MOSI, D32: BLK. | ||
** https://manuals.plus/asin/B0D6QXC813 | |||
* Temperature probe; THERMOPRO copy (including TP20, TP17, and TP-16, TP-16S,TP08S, TP25, TP07, TP17H, TP27, TP06S, TP09, TP28). Max temp 380°C (716°F) with 3.5 mm stereo jack. | * Temperature probe; THERMOPRO copy (including TP20, TP17, and TP-16, TP-16S,TP08S, TP25, TP07, TP17H, TP27, TP06S, TP09, TP28). Max temp 380°C (716°F) with 3.5 mm stereo jack. | ||
* Battery pack: Battery Shield V3 Raspberry Pi / Arduino / ESP32 - 1x 18650 (from FunDuino) | * Battery pack: Battery Shield V3 Raspberry Pi / Arduino / ESP32 - 1x 18650 (from FunDuino) | ||
Revision as of 15:19, 3 July 2026
Introduction
A simple (but updatable) cooking thermometer based on ESP32.
Functions
- Measure, log, display and save the temperature
- Send data using bt or create a local web server which shows the data.
- Allow taking timed photos (a photo at a given time) and show it on a (saved) temp log.
Material
-
The ESP 32
-
The front side of the ESP32 with the display
-
The battery shield from the front.
-
The battery shield from the back. The two leds1, L1 and L2 are in the middle of the board.
-
A sample file from the provider.
List
- ESP32: ideaspark® ESP32 Entwicklungsboard 1,14 Zoll 135x240 full color LCD-Display,CH340,WiFi+BL. ST7789 driver, I2C. CH340
- Display area: 14.864 × 24.912 mm2
- Panel size: 17.6 × 31.0 × 1.6 mm3
- Display current 20mA.
- Display ports: VCC: VCC, GND: GND, D2(GPIO2): DC, D4: RST, D15: CS, D18: SCLK, D23: MOSI, D32: BLK.
- https://manuals.plus/asin/B0D6QXC813
- Temperature probe; THERMOPRO copy (including TP20, TP17, and TP-16, TP-16S,TP08S, TP25, TP07, TP17H, TP27, TP06S, TP09, TP28). Max temp 380°C (716°F) with 3.5 mm stereo jack.
- Battery pack: Battery Shield V3 Raspberry Pi / Arduino / ESP32 - 1x 18650 (from FunDuino)
ESP32
Powering
- Never connect an external power source to the 3V3 pin while powering the ESP32 board via USB. This will cause damage to many boards!
- The VIN pin (sometimes labeled V5 or V5.0) can be used to power the ESP32 with an external regulated 5V DC power source
- you can power your ESP32 development board via the 3V3 pin.
Battery Pack
No reverse voltage protection!
The charging voltage is 4.2 V and the charging current is 500 mA. Note the on/off switch, when plugging or unplugging the lipo battery, the On/OFF switch only switches the USB port. The 3 x 3 V and 3 x 5 V solder pins cannot be switched on and off by this switch
Deep discharge protection
The charging process on the module is indicated by a LED. Red means that the battery is charging and green signifies that charging is complete.
The battery shield connec
