Inkstitch machine embroidery: Difference between revisions
From wikiluntti
(Created page with "== Introduction == https://inkstitch.org/ Forum: https://inkscape.org/forums/embroidery/ == The machine == https://inkstitch.org/tutorials/embroidery-machine/ 3d printed parts: https://www.thingiverse.com/thing:3216283") |
|||
| Line 10: | Line 10: | ||
3d printed parts: https://www.thingiverse.com/thing:3216283 | 3d printed parts: https://www.thingiverse.com/thing:3216283 | ||
Parts list | |||
{| class="wikitable" style="vertical-align:middle; background-color:#FFF;" | |||
|- | |||
! Item | |||
! | |||
! Length | |||
! | |||
|- | |||
! Nema 17 stepper | |||
! | |||
! 3 | |||
! Anything that suits 3D printers or similar applications | |||
|- | |||
| Nema 23 stepper | |||
| | |||
| 1 | |||
| This drives sewing, bigger is better | |||
|- | |||
| Stepper driver TB6600 | |||
| | |||
| 1 | |||
| Or similar to suit sewing machine stepper | |||
|- | |||
| Arduino uno | |||
| | |||
| 1 | |||
| | |||
|- | |||
| GRBL shield for uno | |||
| | |||
| 1 | |||
| Make sure it is equipped with 4 stepper driver places | |||
|- | |||
| DRV8825 | |||
| | |||
| 3 | |||
| Stepper drivers for nema 17 steppers | |||
|- | |||
| Jumpers | |||
| | |||
| 9 | |||
| For micro stepping configuration | |||
|- | |||
| Jumper wires | |||
| | |||
| x | |||
| Connecting sewing machine stepper driver and controls | |||
|- | |||
| Connecting wires | |||
| | |||
| x | |||
| Connecting everything else | |||
|- | |||
| 8mm linear slide | |||
| 400mm | |||
| 4 | |||
| Stainless rods or better | |||
|- | |||
| LM8UU | |||
| | |||
| 8 | |||
| 8mm linear bearings | |||
|- | |||
| 624ZZ bearings | |||
| | |||
| 6 | |||
| Tightening bearings for belt | |||
|- | |||
| 8mm GT2 belt | |||
| 3M | |||
| | |||
| Or 3x 800mm | |||
|- | |||
| GT2 pulley 16 Teeth | |||
| | |||
| 3 | |||
| Suitable for nema17 steppers | |||
|- | |||
| Mounting for big stepper | |||
| | |||
| 1 | |||
| Depends on what was used | |||
|- | |||
| Gear and belt for machine | |||
| | |||
| | |||
| Timing belt or chain, to keep machine on sync. | |||
|} | |||
Revision as of 13:04, 28 February 2026
Introduction
Forum: https://inkscape.org/forums/embroidery/
The machine
https://inkstitch.org/tutorials/embroidery-machine/
3d printed parts: https://www.thingiverse.com/thing:3216283
Parts list
| Item | Length | ||
|---|---|---|---|
| Nema 17 stepper | 3 | Anything that suits 3D printers or similar applications | |
| Nema 23 stepper | 1 | This drives sewing, bigger is better | |
| Stepper driver TB6600 | 1 | Or similar to suit sewing machine stepper | |
| Arduino uno | 1 | ||
| GRBL shield for uno | 1 | Make sure it is equipped with 4 stepper driver places | |
| DRV8825 | 3 | Stepper drivers for nema 17 steppers | |
| Jumpers | 9 | For micro stepping configuration | |
| Jumper wires | x | Connecting sewing machine stepper driver and controls | |
| Connecting wires | x | Connecting everything else | |
| 8mm linear slide | 400mm | 4 | Stainless rods or better |
| LM8UU | 8 | 8mm linear bearings | |
| 624ZZ bearings | 6 | Tightening bearings for belt | |
| 8mm GT2 belt | 3M | Or 3x 800mm | |
| GT2 pulley 16 Teeth | 3 | Suitable for nema17 steppers | |
| Mounting for big stepper | 1 | Depends on what was used | |
| Gear and belt for machine | Timing belt or chain, to keep machine on sync. |
