Arduino Sound Sensor

Introduction

Simple sound sensor; output True or False.

See https://www.atomic14.com/2020/09/12/esp32-audio-input

Digital Sound sensor

Code 1. The simple

Tutorial page: https://arduinogetstarted.com/tutorials/arduino-sound-sensor

#define SENSOR_PIN 7

int lastState = HIGH;  // the previous state from the input pin
int currentState;      // the current reading from the input pin

void setup() {
  Serial.begin(9600);
  pinMode(SENSOR_PIN, INPUT);
}

void loop() {
  currentState = digitalRead(SENSOR_PIN);
  if (currentState){
     Serial.println( currentState );
  }else{
     Serial.print("Schii");
  }

}

Code 1

Turn on the one more LED if the sound is strong enough.

#include <FastLED.h>

#define SENSOR_PIN 7
#define NUM_LEDS 10
#define LED_PIN 5

int soundState = HIGH;  // the previous state from the input pin
int numLeds = 0;
CRGB leds[NUM_LEDS];


void setup() {
  Serial.begin(9600);
  pinMode(SENSOR_PIN, INPUT);
  FastLED.addLeds<WS2812B, LED_PIN, GRB>(leds, NUM_LEDS);
  FastLED.setBrightness(20);
}

void loop() {
  soundState = digitalRead(SENSOR_PIN);
  if (soundState){
    numLeds++;
  }

  for (int i=0; i<min( numLeds, NUM_LEDS); i++){
    leds[i] = CRGB::Green;
    FastLED.show();
  }

  if (soundState){
    Serial.println("");
     Serial.println( soundState );
  }else{
     Serial.print("Schii");
  }

}

Code 2

1. Turn all the LEDS to black in the SetUp()
2. Add delay when sound is noticed (not two LEDs turning on at the same time).
3. turn of the last led after a while.

Code 3: test

#include <FastLED.h>

// Arduino's pin connected to OUT pin of the sound sensor
#define SENSOR_PIN 7
#define NUM_LEDS 10
#define LED_PIN 5

int soundState = HIGH;  // the previous state from the input pin
int numLeds = 0;
CRGB leds[NUM_LEDS];
unsigned long turnOffStart;

void setup() {
  Serial.begin(9600);
  pinMode(SENSOR_PIN, INPUT);
  FastLED.addLeds<WS2812B, LED_PIN, GRB>(leds, NUM_LEDS);
  FastLED.setBrightness(20);
  for (int i=0; i<NUM_LEDS; i++){
    leds[i] = CRGB::Black;
    FastLED.show();
  }
  turnOffStart = millis();

}



void loop() {
  soundState = digitalRead(SENSOR_PIN);
  if (soundState){
    numLeds++;
    turnOffStart = millis();
    delay(50);

  }
  if (millis() - turnOffStart > 200){
    turnOffStart = millis();
    numLeds = max( 0, numLeds--);
  }

  for (int i = min( numLeds, NUM_LEDS); i<NUM_LEDS; i++){
    leds[i] = CRGB::Black;
    FastLED.show();
  } 

  for (int i=0; i<min( numLeds, NUM_LEDS); i++){
    leds[i] = CRGB::Green;
    FastLED.show();
  }

}

HQ: Gravity: Analog Sound Level Meter

https://www.dfrobot.com/product-1663.html and the Wiki https://wiki.dfrobot.com/Gravity__Analog_Sound_Level_Meter_SKU_SEN0232

MAX4466 / GY4466

MAX4466 Microphone Amplifier Module

MAX9814

Electret Microphone Amplifier - MAX9814 with Auto Gain Controller is a mic with integrated pre-amp plus audio amplifier. It is analog.

INMP441

Digital I2S MEMS microphone.

SPH0645

Digital I2S MEMS microphone.

LM358 Operational Amplifier Module

To amplify the analog data.