Fixing of a Mobile phone: Difference between revisions

From wikiluntti
VisualWikitext
 
(10 intermediate revisions by the same user not shown)
Line 11: Line 11:
* Dimensions: 157.6 x 74.1 x 7.8 mm3, 6.4", 1440x3040 pixels
* Dimensions: 157.6 x 74.1 x 7.8 mm3, 6.4", 1440x3040 pixels


Ifixit part number IF416-001-3 AMOLED (252€). Replacement guide: https://www.ifixit.com/Guide/Samsung+Galaxy+S10++Screen+Replacement/136889
Ifixit part number IF416-001-3 AMOLED (252€).  
Replacement guide:  
* https://www.ifixit.com/Guide/Samsung+Galaxy+S10++Screen+Replacement/136889
* https://www.youtube.com/watch?v=0ZZs7rv4ifA


Tools and parts:
Tools and parts:
* Suction cup
* iOpener: an insulated, heat-retaining bag. https://www.ifixit.com/Guide/iOpener+Instructions/11677
* iOpener: an insulated, heat-retaining bag. https://www.ifixit.com/Guide/iOpener+Instructions/11677
* isopropyl alcohol  
* isopropyl alcohol  
Line 20: Line 24:
* Display adhesive
* Display adhesive
* Rear cover adhesive
* Rear cover adhesive
=== My fix ===
<gallery>
Mobile backcoverremoved.jpg| Tools needed to remove the backcover: heat gun, sucker and plectrum
Mobile backremoved.jpg|Remove the backcover.
Mobile bottompart.jpg| Remove the bottom part.
Mobile mainboard.jpg | Mainboard. Remove the camera module (upper left corner) and SIM card tray.
Mobile mainboardtoNew.jpg| Insert the mainboard to the new display. Remember to change the vibrator and phone plug.
Mobile checkthecables.jpg| Ensure that the cable looks similar and that the screen is of right size
Mobile working.jpg| Check that the phone works. The put the black plastic parts into their place
Mobile glueing.jpg| Glueing is difficult.
</gallery>
Remove the backcover
Back cover's right edge
* Heat (to < 100˚C) back cover's right edge (there is less adhesive) for two (2) minutes.
* Suction cup to a center of right edge
* Slice through the right edge
Bottom edge
* Heat for 2 min
Remaining edges. Be careful with the corners.
* Remove the back cover from the frame.
The midframe
* Remove the nine 4mm Phillips screws from the to midframe.
* Loosen the plastic clips.
* Loosen the midframe from the notch on the left edge of the phone (near the power button).
* Disconnect the battery
* Remove the battery
* Find the plastic clips
Remove the main board
* Remove the camera
* Remove the vibrator
* Remove the phone audio plug
* Remove the SIM card
Insert all to the new display
* Glue the back cover

Latest revision as of 21:11, 17 April 2025

Introduction

Display (screen) replacement

Samsung Galaxy S10+

Samsung Galaxy S10+

  • SN: r58m78at7wf
  • SM-G975F
  • SM-G975FZWDNEE
  • Dimensions: 157.6 x 74.1 x 7.8 mm3, 6.4", 1440x3040 pixels

Ifixit part number IF416-001-3 AMOLED (252€). Replacement guide:

Tools and parts:

Also the adhesives are needed

  • Display adhesive
  • Rear cover adhesive

My fix

  • Tools needed to remove the backcover: heat gun, sucker and plectrum

    Tools needed to remove the backcover: heat gun, sucker and plectrum

  • Remove the backcover.

    Remove the backcover.

  • Remove the bottom part.

    Remove the bottom part.

  • Mainboard. Remove the camera module (upper left corner) and SIM card tray.

    Mainboard. Remove the camera module (upper left corner) and SIM card tray.

  • Insert the mainboard to the new display. Remember to change the vibrator and phone plug.

    Insert the mainboard to the new display. Remember to change the vibrator and phone plug.

  • Ensure that the cable looks similar and that the screen is of right size

    Ensure that the cable looks similar and that the screen is of right size

  • Check that the phone works. The put the black plastic parts into their place

    Check that the phone works. The put the black plastic parts into their place

  • Glueing is difficult.

    Glueing is difficult.

Remove the backcover

Back cover's right edge

  • Heat (to < 100˚C) back cover's right edge (there is less adhesive) for two (2) minutes.
  • Suction cup to a center of right edge
  • Slice through the right edge

Bottom edge

  • Heat for 2 min

Remaining edges. Be careful with the corners.

  • Remove the back cover from the frame.

The midframe

  • Remove the nine 4mm Phillips screws from the to midframe.
  • Loosen the plastic clips.
  • Loosen the midframe from the notch on the left edge of the phone (near the power button).
  • Disconnect the battery
  • Remove the battery
  • Find the plastic clips

Remove the main board

  • Remove the camera
  • Remove the vibrator
  • Remove the phone audio plug
  • Remove the SIM card

Insert all to the new display

  • Glue the back cover
Retrieved from "https://wiki.luntti.net/index.php?title=Fixing_of_a_Mobile_phone&oldid=13488"