Inkstitch machine embroidery: Difference between revisions
| (14 intermediate revisions by the same user not shown) | |||
| Line 6: | Line 6: | ||
== The machine == | == The machine == | ||
=== jameskolme === | |||
https://inkstitch.org/tutorials/embroidery-machine/ | https://inkstitch.org/tutorials/embroidery-machine/ | ||
| Line 19: | Line 21: | ||
! | ! | ||
|- | |- | ||
| Nema 17 stepper | | Nema 17 stepper (Φ5mm) | ||
| | | | ||
| 3 | | 3 | ||
| Anything that suits 3D printers or similar applications | | Anything that suits 3D printers or similar applications | ||
|- | |- | ||
| Nema 23 stepper | | Nema 23 stepper (Φ8mm) | ||
| | | | ||
| 1 | | 1 | ||
| Line 32: | Line 34: | ||
| | | | ||
| 1 | | 1 | ||
| Or similar to suit sewing machine stepper | | Or similar to suit sewing machine stepper (Nema23) | ||
|- | |- | ||
| Arduino uno | | Arduino uno | ||
| Line 47: | Line 49: | ||
| | | | ||
| 3 | | 3 | ||
| Stepper drivers for | | Stepper drivers for Nema17 steppers | ||
|- | |- | ||
| Jumpers | | Jumpers | ||
| Line 53: | Line 55: | ||
| 9 | | 9 | ||
| For micro stepping configuration | | For micro stepping configuration | ||
|- | |- | ||
| 8mm linear slide | | 8mm linear slide | ||
| Line 83: | Line 80: | ||
| 3 | | 3 | ||
| Suitable for nema17 steppers | | Suitable for nema17 steppers | ||
|- | |- | ||
| Gear and belt for machine | | Gear and belt for machine | ||
| Line 97: | Line 89: | ||
"Driving stepper with closed loop operation." | "Driving stepper with closed loop operation." | ||
"Thin oil. Make sure sewing machine is oiled well (don’t over do it). One drop of oil every oiling location. If flooded wipe it. Fabric, thread and dust will collect on excess oil." | |||
Nema17 | |||
* 12-24VDC | |||
* 1.5A | |||
* 5mm | |||
* 42Ncm | |||
Nema23 | |||
* 24-48VDC | |||
* 4.0A | |||
* 8mm | |||
* 2.4Nm | |||
The A4988 is a complete microstepping motor driver | |||
* Up to 35 V and ± 2 A | |||
* 3.3 and 5 V compatible logic supply | |||
* Thermal shutdown circuit | |||
* Ground fault protection | |||
=== Other ideas === | |||
https://www.instructables.com/Embroidery-Machine/ | |||
== References == | |||
https://embroidery-pro.com/inkstitch-basic-usage/ | |||
https://meowfire.com/ink-stitch-embroidery-on-a-brother-lb5000/ | |||
https://www.youtube.com/watch?v=iqLGE7gDG_A | |||
https://www.machineembroiderygeek.com/how-to-digitize-an-applique-design-using-ink-stitch-for-free/ | |||
https://fedoramagazine.org/diy-embroidery-with-inkscape-and-ink-stitch/ | |||
https://www.inkandstitchsolutions.com/embroidery/ | |||
Latest revision as of 18:00, 1 March 2026
Introduction
Forum: https://inkscape.org/forums/embroidery/
The machine
jameskolme
https://inkstitch.org/tutorials/embroidery-machine/
3d printed parts: https://www.thingiverse.com/thing:3216283
Parts list
| Item | Length | # | |
|---|---|---|---|
| Nema 17 stepper (Φ5mm) | 3 | Anything that suits 3D printers or similar applications | |
| Nema 23 stepper (Φ8mm) | 1 | This drives sewing, bigger is better | |
| Stepper driver TB6600 | 1 | Or similar to suit sewing machine stepper (Nema23) | |
| Arduino uno | 1 | ||
| GRBL shield for uno | 1 | Make sure it is equipped with 4 stepper driver places | |
| DRV8825 | 3 | Stepper drivers for Nema17 steppers | |
| Jumpers | 9 | For micro stepping configuration | |
| 8mm linear slide | 400mm | 4 | Stainless rods or better |
| LM8UU | 8 | 8mm linear bearings | |
| 624ZZ bearings | 6 | Tightening bearings for belt | |
| 8mm GT2 belt | 3M | Or 3x 800mm | |
| GT2 pulley 16 Teeth | 3 | Suitable for nema17 steppers | |
| Gear and belt for machine | Timing belt or chain, to keep machine on sync. |
"Driving stepper with closed loop operation."
"Thin oil. Make sure sewing machine is oiled well (don’t over do it). One drop of oil every oiling location. If flooded wipe it. Fabric, thread and dust will collect on excess oil."
Nema17
- 12-24VDC
- 1.5A
- 5mm
- 42Ncm
Nema23
- 24-48VDC
- 4.0A
- 8mm
- 2.4Nm
The A4988 is a complete microstepping motor driver
- Up to 35 V and ± 2 A
- 3.3 and 5 V compatible logic supply
- Thermal shutdown circuit
- Ground fault protection
Other ideas
https://www.instructables.com/Embroidery-Machine/
References
https://embroidery-pro.com/inkstitch-basic-usage/
https://meowfire.com/ink-stitch-embroidery-on-a-brother-lb5000/
https://www.youtube.com/watch?v=iqLGE7gDG_A
https://www.machineembroiderygeek.com/how-to-digitize-an-applique-design-using-ink-stitch-for-free/
https://fedoramagazine.org/diy-embroidery-with-inkscape-and-ink-stitch/
